Stencil making
How to make a tattoo stencil from a photo or drawing
Updated November 12, 20267 min read
Save to PinterestA tattoo stencil is a line drawing in purple transfer ink, pressed onto skin as a guide. Making one takes four decisions: which lines to keep, how heavy they are, how big the piece is, and how the lines get onto transfer paper.
This guide covers each step, with a thermal printer and without one.
Quick answer
To make a tattoo stencil, turn your reference into clean black line art, size it in centimetres, then put it on transfer paper. Print it at 100% through a thermal printer, or lay the artwork on hectograph paper and trace every line with a ballpoint pen. The purple lines land on the underside of the white sheet, ready to press onto skin.
- Layers in transfer paper
- 4
- Print scale, with fit to page off
- 100%
- Open skin between lines
- 1.5 to 2 mm
- Line weights from one upload
- 3
Step by step
Make a tattoo stencil from a photo or drawing
What you need
- Reference photo or drawing
- Thermal or hectograph transfer paper
- Plain paper for a test print
- Masking tape
Tools
- Phone, tablet or computer
- Thermal stencil printer, or a ballpoint pen
- Ruler
- Scissors
- 01
Choose and clean up the reference
Pick a sharp, evenly lit image in which the subject fills the frame. Crop away the background and raise the contrast until the edges are obvious.
- 02
Turn it into line art
Trace the outlines and the main shadow edges by hand, in a drawing app, or with a photo to stencil converter. Leave out texture you will not tattoo.
Tip: TattooStencil returns Fine, Standard and Bold versions from one upload, and its Retouch eraser removes stray lines.
- 03
Match the line weight to the size
Thin lines suit small, detailed pieces. Heavy lines suit large pieces and strong shapes. Keep roughly 1.5 to 2 mm of open skin between neighbouring lines at the final size.
- 04
Size it in centimetres
Measure the placement on the body and set the design to that width. Print at 100% with fit to page switched off.
Tip: The TattooStencil PDF carries a 50 mm calibration bar. If it measures 50 mm, the stencil is the size you entered.
- 05
Check whether to mirror
Trace or print a short word first. It should look backwards on the ink side of the sheet, so that it reads correctly on skin.
- 06
Put the lines on transfer paper
With a thermal printer, remove the protective tissue and feed the sheet as the maker instructs. By hand, tape the artwork over the white sheet, pull the tissue out and trace every line with a ballpoint pen.
- 07
Inspect and trim
Lift the white sheet and check its underside. The purple lines should be solid and unbroken. Retrace anything faint, then cut around the design.
Turn the reference into clean line art
A stencil is a map, not a copy. It shows where the outlines, hard edges and main shadow shapes go. Skin texture, soft gradients and background clutter make it harder to read.
Three routes get you there, and all end in black lines on a white background at the size you will tattoo.
- Hand tracing
- Print the reference at the final size, lay tracing paper over it and draw the lines you want to keep.
- Drawing app on an iPad
- Import the photo, lower its opacity and trace on a new layer with a hard black brush. Export the lines on white.
- Photo to stencil converter
- Upload the photo, let the converter trace the main lines, then erase what you do not need.
Choose line weight and size together
Line weight and size depend on each other. A thin line that looks delicate at 15 cm can vanish at 5 cm, and heavy lines that read well on a thigh will fill in on a wrist.
Decide the size first. Then pick the lightest weight that still shows clearly at that size, and remove detail wherever lines sit closer than about 1.5 to 2 mm. Each design in the TattooStencil library lists its smallest good width in centimetres.
| Line weight | Best for | Watch for |
|---|---|---|
| Fine | Small or detailed pieces | Lines too faint to follow once transferred |
| Standard | Most designs | Tight areas such as eyes and lettering |
| Bold | Large pieces and strong shapes | Close lines merging at small sizes |
How transfer paper works
Thermal and hectograph transfer paper is a sandwich of four sheets. Heat or pen pressure pushes ink from the purple carbon sheet onto the underside of the white sheet. That underside is the stencil.
The tissue only protects the carbon, and comes out before you print or trace.
Making a stencil without a thermal printer
You do not need a machine. Print or draw the design at its final size on plain paper, tape it over the white master sheet and pull out the protective tissue.
Trace every line with a ballpoint pen on a hard, smooth surface, with firm, even pressure. Lift a corner now and then to check that the purple line underneath is solid.
Without transfer paper the options narrow: stencil ink in an inkjet printer onto tracing paper, or drawing straight onto skin with skin markers.
Do you need to mirror the stencil?
Usually not. The surface that touches the skin transfers as a mirror image. With hand tracing, thermal copiers and thermal printers loaded as the maker instructs, the ink sits on the underside of the white sheet, already reversed, so it reads correctly on skin.
Mirror the artwork in two cases: when the printed face itself touches the skin, as with stencil ink printed onto tracing paper, or to flip the design on purpose, such as a profile that should face toward the chest.
Common questions
How do I make a tattoo stencil from a photo?
Crop the photo, raise the contrast and turn it into black line art, by tracing or with a photo to stencil converter. Size it in centimetres, print at 100%, then thermal print it or hand trace it over transfer paper.
Can I make a tattoo stencil at home without a thermal printer?
Yes. Tape the design over the white sheet of hectograph transfer paper, remove the protective tissue and trace every line with a ballpoint pen. The stencil forms on the underside of the white sheet.
Can I make a tattoo stencil without transfer paper?
Two routes are common: an inkjet printer filled with stencil ink, printing mirrored artwork onto tracing paper, or drawing directly on skin with skin markers. A print in ordinary ink will not transfer.
How do I make a tattoo stencil on an iPad?
Trace the reference on a separate layer in a drawing app, in solid black, and export the lines on white. Or upload the photo to TattooStencil in the browser and download a PNG or a true-size PDF.
Do I need to mirror a tattoo stencil?
Not with hand tracing or a correctly loaded thermal printer: the ink is already reversed on the underside of the sheet. Mirror only when the printed face touches the skin, or to flip the design on purpose.
Stencil making
Make your stencil now
Upload a photo or drawing and get Fine, Standard and Bold versions. Erase stray lines, mirror the design if needed, then download a PNG or a true-size PDF in exact centimetres. The stencil maker is free to try.
Keep reading
All guidesStencil application
How to apply a tattoo stencil so it stays put
Apply a tattoo stencil step by step: shave and clean, a thin layer of primer, place it with the client standing, press, peel, then dry 10 to 15 minutes.
Printer setup
Thermal tattoo stencil printer settings: scale, paper and density
Set up a thermal stencil printer: print at 100% actual size, load four-layer paper correctly, raise density for faint lines and keep the print head clean.
Size and placement
Tattoo size and placement guide: how big, and where
How big should a tattoo be? Minimum sizes by style in cm, why small detailed tattoos blur over the years, and how placement changes how a tattoo ages.